Er zijn nog geen producten in uw winkelwagen geplaatst.
NIEUW
Â
38 / 83
Bezig met laden...
RC Car Colours Lexan Aprillia Green nr944 150ml
€ 6,50
RC Car Colours Lexan Aprillia Green nr944 150ml
RC Car Colours Lexan White Metalic nr934 150ml
€ 6,50
RC Car Colours Lexan White Metalic nr934 150ml
RC Car Colours Lexan Green Metalic nr934 150ml
€ 6,50
RC Car Colours Lexan Green Metalic nr934 150ml
RC Car Colours Lexan Purpele Metalic nr930 150ml
€ 6,50
RC Car Colours Lexan Purpele Metalic nr930 150ml
RC Car Colours Lexan Silver Glitter nr924 150ml
€ 6,50
RC Car Colours Lexan Silver Glitter nr924 150ml
RC Car Colours Lexan Fluo Magenta nr1012 150ml
€ 6,50
RC Car Colours Lexan Fluo Magenta nr1012 150ml
RC Car Colours Lexan Fluo Deep Orange nr1011 150ml
€ 6,50
RC Car Colours Lexan Fluo Deep Orange nr1011 150ml
RC Car Colours Lexan Fluo Deep Red nr1010 150ml
€ 6,50
RC Car Colours Lexan Fluo Deep Red nr1010 150ml
RC Car Colours Lexan Cuypers Pink nr1009 150ml
€ 6,50
RC Car Colours Lexan Cuypers Pink nr1009 150ml
Rockamp Damper Tang
€ 16,95
Working on the shock absorbers is comparatively easy with these pliers. Thanks to the light and multifunctional design, there are several ways to use the pliers, for example to remove the ball shells. In addition, the material prevents damage and scratches on the shock absorbers.
Technical Specifications
| Length: | 151mm |
| Width: | 37.5mm |
| Height: | 9.1mm |
| Weight: | 70g |
LANGE LIJMNAALDEN SET 5 STUKS MMC
€ 3,95
LANGE LIJMNAALDEN SET 5 STUKS MMC
VOOR BV BANDEN TE LIJMEN.
ALU REAR ROLL-CENTER HOLDER FOR ANTI-ROLL BAR - 7075 T6
€ 36,95
ALU REAR ROLL-CENTER HOLDER FOR ANTI-ROLL BAR - 7075 T6
Hobbywing Xerun Bandit Brushless Motor G4 13.5T 3200kV
€ 123,95
Product information "Hobbywing Xerun Bandit Brushless Motor G4 13.5T 3200kV"
Those who are eager for high torque performance in 1/10 Outlaw competitions will make the right choice with the Xerun Bandit G4 motor series. This motor proves to be up to 18% more powerful and 12% more efficient compared to its G2R predecessor. With the fully adjustable timing ranging from 20 to 60 degrees, the full potential of the Bandit G4 is unleashed. The motor adopts a fully exposed stator core structure, meaning that the outer stator core is directly exposed to maximize heat dissipation performance.
Features:
- More power than the Xerun Bandit G2R series
- Dual sensor design for optimal wiring in RC car
- New motor housing with optimized cooling openings
- Adjustable timing from 20-60°
- High-precision manufactured rotor (5-13.9*24.1-AUS)
- High temperature tolerance of the winding
- Easily disassembled for maintenance
Technical Specifications:
| Winding: | 13.5T |
| Type: | Sensored Brushless |
| kV Rating: | 3200KV |
| Max. Power Output: | 387W |
| Max. Current: | 48A |
| No-Load Current: | 5.13A |
| LiPo Cells: | 2-3S |
| Poles: | 2 |
| Timing (adjustable): | 20-60° |
| Diameter: | 35.8mm |
| Length: | 53.9mm |
| Shaft Diameter: | 3.175mm |
| Shaft Length: | 14mm |
| Weight: | 187.6g |
| Application: | 1/10 Stock, Outlaw Races |
Delivery:
1x Xerun Bandit G4-Motor "13.5T", Type "Torque"
1x Sensor cable
1x Manual
TAMIYA Body set Volkswagen Golf II GTI 16V Rally met certificaat
€ 42,50
Body set Volkswagen Golf II GTI 16V Rally met certificaat
UV LIJMKIT SET MMC
€ 14,95
UV LIJM KIT MET STERKE UV 8 LED LAMP
VOOR HET REAPAREREN VAN BODY'S
EN VOOR DIV LIJM KLUSSEN.
TAMIYA RM01 3x31mm Titanium Coated King Pin (2)
€ 12,50
RM01 3x31mm Titanium Coated King Pin (2)
Deze king-pins hebben een duurzame titanium coating om het soepel laten bewegen van de Uprights te verhogen.
Specificaties en functies:
- 3x31mm Titanium Coated King Pin x 2
- Compatibel met RM-01 chassis.
Tamiya nummer: 54355
MASTER GigaProp 6 Set (Mode 2 + 4)PICHLER
€ 139,95
MASTER GigaProp 6 Set (Mode 2 + 4)
De telemetrie 6-kanaals afstandsbediening MASTER GigaProp 6 wordt gekenmerkt door zijn gebruiksgemak en heeft diverse instellingen voor b.v. electronische mixer en speciale programma´s. Het grote, hoog display kan eenvoudig worden afgelezen, zelfs in fel zonlicht. De zender is zeer smal (slechts 40 mm) en ligt dus goed in de hand.
bestek
- Radio systeem: 2.4Ghz
- 6 Kanalen
- Telemetrie: geïntegreerd (optionele sensors, zie onder "Speciale toebehoren")
MASTER zender GigaProp 6
- 6 Kanalen
- Zendvermogen: <20 dBm
- RF kanalen: 140
- Bandbreedte: 500kHz
- Resolutie: 4096 stappen
- Alarm niveau als de accuspanning <4.2V
- Gewicht zender. ongeveer 405g
- Afmetingen zender: 200 x 170 x 40mm
- Scherm afmetingen: 73 x 39mm, 128 x 64 pixels
- Model geheugen: 20
- Trim: Digital
- Display: LCD / STN Transflectief achtergrondverlichting
- Spanning: 6V DC 1.5AA x4 (NiMH of alkaline, niet meegeleverd)
- Behuizing: stevig ABS
- Sender software: te updaten
- Sticks: aluminium, in lengte verstelbaar
- Stick Mode: Zelfs met terugwerkende kracht van mode 2/4 (gas links) naar mode 1/3 (gas rechts) ombouwbaar
Ontvanger MASTER 6K Telemetrie
- 6 Kanalen
- Afmetingen (L / B / H): 48 x 26 x 10 / 15mm
- Gewicht: 14g
- RF Gevoeligheid: -105dBm
- Bedrijfsspanning: 4,0 .. 6.5V DC
- Resolutie: 1024 stappen
Leveromvang:
- 1x zender MASTER GigaProp 6
- 1x Receiver MASTER 6K Telemetrie
- Binding plug
- USB-aansluitkabel
- Handleiding Duits, Engels
optionele accessoires
- NiMH-accu 1,2V 2550mAh, 950010
- Spanning sensor (tot 100V), C8960
- Temperatuur sensor (tot 250 ° C), C8959
- RPM sensor optisch (. 60.000 omw./min) C8958
- RPM sensor magnetisch (. 60.000 omw./min) C8957
- Vario-sensor, C9024
- IBus module, C8961
- Ontvanger MASTER 6K Telemetrie, C8962
- Leraar / leerling-kabel, C9020
- Flight Simulator Aansluitset voor PC / USB-poort, C6099
Om de zender te bedienen zijn 4 stuks gewone AA batterijen nodig of 4x NiMh 1,2V 2550mAh (niet inbegrepen).
Pichler nummer: C8802
1:10 EP Monster Truck ""AMT3.4-V2 BL"" 4WD Brushless RTR ABSIMA
€ 289,95
The success story continues! We have equipped the AMT3.4 "V2" with some new features that bring the vehicle to the next level of evolution.
Some technical changes have been implemented in our 1/10th scale Monster Truck - among other things, the vehicle now comes with LED lighting on the roof.
- NEW* 60A brushless speed controller with T connector and 3421KV motor
- NEW* Programmable speed controller
- NEW* 15 kg steering servo with metal gear
- NEW* LED lighting
- NEW* Monster Truck body with many add-on parts
- NEW* even more option parts available
The new 60A brushless speed controller is waterproof, programmable and pre-configured with a T-connector. To fully exploit the potential of the vehicle, we recommend a LiPo 2S/7.4V battery for operation. In addition, a separately available programming box (item 2110062) can be used to adjust various parameters such as braking force, punch, low-voltage protection and more.
The car is powered by a 3421KV brushless motor that directly accesses the all-wheel drive. The two differentials (front and rear) are driven by an aluminium drive shaft. A 15kg metal gear servo handles the conversion of the steering commands.
The motor/controller unit can also be powered by a 3S/11.1V LiPo battery (note the size of the battery compartment!), but this increases the wear and tear on the vehicle extremely. Also the handling becomes almost impossible due to the enormous over-motorization. Therefore, we generally advise against 3S driving.
4 adjustable aluminum oil-pressure shock absorbers offer ideal handling, so that a lot of driving fun. The spring preload can be adjusted via a knurled screw. Thus, the chassis can be perfectly adapted to your needs.
Lightweight and compact design, as well as comfortable and ergonomically shaped - these are just two features of our CR4S 4-channel remote control. Of course, all trim, reverse and dual rate functions are available in the cockpit, making adjustments easy via levers and knobs. In addition, the remote control has a "Beginner Mode" (speed reduction by 50%) and is therefore ideal for pilots who do not yet have so much experience with the handling of such RC vehicles.
- 4WD all wheel drive
- 2.4GHz 4-channel radio system
- 60A brushless speed controller (waterproof; T plug; programmable)
- 3421KV brushless motor (sensorless; splash-proof)
- 15kg metal gear steering servo (25T; ball bearings)
- 8 Aluminium oil shock absorbers
- Ball bearing main drive
- Extremely durable composite plastic parts
- Steel differential outdrives
- Aluminium main drive shaft with steel mounts
- Adjustable upper tie rods
- 5mm aluminium engine mount
- 6mm shock towers
- 2 differentials (front/rear)
- Stylish Monster Truck body with add-on parts
- "Light-Weight" chassis (less weight - longer driving time)
- Many aluminum option parts available
- Scale: 1:10
- Dimensions (L/W/H): 425x300x200 mm
- Weight: 2090g
- Wheelbase: 270mm
- Ground clearance: approx. 45mm
- Track width: 250mm front/rear
- Wheels front/rear: Ø 116mm / Width: 57mm
- Shock absorber oil: 400CPS
- Shock absorber installation length: 100mm
- Motor ratio: 17T / main gear: 64T (module 0.6)
- 1/10 Brushless Monster Truck "AMT3.4BLV2" RTR
- 2.4GHz CR4S radio
- Sticker sheet
- Manual
- 4 AA batteries for radio
- 7.4V/2S LiPo car battery
- Charger (suitable for car battery)
- Programming box for individual settings of the speed controller
1:10 EP Truggy "AT3.4-V2 KIT" 4WD KIT ABSIMA
€ 109,95
The success story continues! We have equipped the AT3.4 "V2" KIT with some new features that take the vehicle to the next evolutionary stage
Some technical changes have been made to our 1:10 Truggy - among other things, the vehicle now comes with LED lighting on the roof
- NEW* Body in new race design
- NEW* LED lighting
- NEW* Downforce rear wing
- NEW* even more tuning parts available
The KIT version is a kit that can be assembled with standard tools such as pliers and screwdrivers. Shock absorbers and gearbox units are already pre-assembled so that even children can build this vehicle under parental supervision. You can also decide for yourself which electronic components should be installed in the vehicle. The kit includes 2 gear units - a copper/plastic version with the gear ratio for brushed motors and a full metal version designed for a brushless drive. This means that there are no limits to the motorization.
- 4WD all-wheel drive
- 4 oil shock absorbers
- Ball bearing main drive
- Extremely durable composite plastic parts
- Steel differential outlets
- Aluminum main drive shaft with steel mounts
- Adjustable upper tie rods
- 5mm aluminum motor mount
- 6mm shock towers
- 2 differentials (front/rear)
- Stylish Truggy body with add-on parts
- "Light-Weight" chassis (less weight - longer driving time)
- Many aluminum tuning parts available
- Scale 1:10
- Dimensions (L/W/H): 405x325x165 mm
- Weight: 1180g
- Wheelbase: 270mm
- Ground clearance: approx. 35mm
- Track width: 270mm front/rear
- Wheels: Ø 105mm / width: 55mm
- Shock absorber oil: 400CPS
- Installation length of the shock absorbers: 90mm
- Gear ratio BRUSHED version: pinion: 18T / main gear: 64T (module 0.6)
- Gear ratio BRUSHLESS version: pinion: 23T / main gear: 64T (module 0.6)
- 1/10 Truggy "AT3.4V2" KIT version
- Sticker sheet
- Manual
- Radio and receiver
- Speed controller and motor (brushed or brushless)
- Steering servo with 25T
- Drive battery (7.2V NiMH or 7.4V/2S LiPo battery)
- Charger (suitable for the drive battery)
- Programming card (optional for individual settings of the speed controller)
- 4* AA batteries for the remote control
1:10 EP Truggy "AT3.4-V2" 4WD RTR ABSIMA
€ 159,95
- NEW* 80A brushed speed controller withT-connector and 540 motor
- NEW* Programmable speed controller
- NEW* 15kg steering servo with metal gears
- NEW* LED lighting
- NEW* Race body with many add-on parts
- NEW* even more option parts available
The new 80A Brushed speed controller is waterproof, programmable and pre-configured with a T-connector. To fully exploit the potential of the vehicle, we recommend a 2S LiPo battery for operation. In addition, a separately available programming card (item 2110061) can be used to set various parameters such as braking force, punch, low voltage protection and more.
The car is powered by a 540size 15T brushed motor that directly accesses the all-wheel drive system. The two differentials (front and rear) are driven by an aluminum driveshaft. Due to the higher power of the speed controller and the use of T-connectors, any 2S LiPo battery can be used - no matter what the C-rate and capacity.
4 oil-pressure shock absorbers provide ideal handling, so there is plenty of driving fun. A 15kg metal gear servo with takes over the implementation of the steering commands.
Lightweight and compact design, as well as comfortable and ergonomically shaped - these are just two features of our CR4S 4-channel remote control. Of course, all trim, reverse and dual rate functions are available in the cockpit, making adjustments easy via levers and knobs. In addition, the remote control has a "Beginner Mode" (speed reduction by 50%) and is therefore ideal for pilots who do not yet have so much experience with the handling of such RC vehicles.
- 4WD all wheel drive
- 2.4 GHz 4-channel radio system
- 80A brushed speed controller with T-plug
- 540size 15T motor with 32.000RPM @ 7.4V
- 15kg MG steering servo (25T, ball bearings)
- Oil shock absorbers
- Ball bearing main drive
- Extremely durable composite plastic parts
- Steel differential outputs
- Aluminum main drive shaft with steel mounts
- Adjustable upper tie rods
- 5mm aluminum motor mount
- 6mm shock towers
- 2 differentials (front/rear)
- Stylish truggy body with add-on parts
- "Light-Weight" chassis (less weight - longer drive time)
- Many aluminum option parts available
- Scale: 1:10
- Dimensions (L/W/H): 405x325x165 mm
- Weight: 1740g
- Wheelbase: 270mm
- Ground clearance: ca. 35mm
- Track width: 270mm front/rear
- Wheels front/rear: Ø 105mm / Width: 55mm
- Shock absorber oil: 400CPS
- Shock absorber installation length: 90mm
- Motor ratio: pinion: 18T / main gear: 64T (module 0,6)
- 1/10 Truggy "AT3.4V2" RTR
- 2.4GHz "CR4S" radio
- Sticker sheet
- Manual
- 4x AA Batteries for radio
- 7.2V NiMH or 7.4V* LiPo car battery (*recommended)
- Charger (suitable for car battery)
- Programm card for individual settings of the speed controller
Â