Dragster-3 14TMOTOR  Carson 

Hobbywing XeRun XR10 Justock G3 ETS ESC & XeRun Justock G2.1 17.5T ETS Motor

Deze Hobbywing combo is het nieuwste aandrijvingspakket voor de FWD klasse in ETS. Het is ook een perfecte combo voor iedereen die van echt stockracen houdt.

De controller is zeer gevoelig en gemakkelijk te bedienen, en de rem werkt geweldig. De 17,5T motor heeft voldoende vermogen en past perfect bij de software van de controller.
Voor gemakkelijke identificatie zijn de regelaar en de motor voorzien van een ETS  lasergravure.
Er is vooraf geïnstalleerde software op de ESC die vervolgens met de ETS in de Fronti-klasse wordt gebruikt.

De ESC kan geprogrammeerd worden via de Hobbywing programmeerbox of de WIFI module.
De kwaliteit van Hobbywing is alom bekend, en deze geweldige voorraadcombo sluit naadloos aan en loopt als een zonnetje!

XeRun XR10 G3 Justock-controller:

• Aluminium behuizing
• vaste condensator
• Bescherming tegen omgekeerde polariteit
• Programmering ook mogelijk via LCD box en WiFi/OTA module!
• BEC naar keuze met 6,0V of 7,4V - instelbaar op 4A
• zwarte motor- en accukabels
• Type: borstelloos met sensor
• Continue stroom: 60A
• Ingangsspanning: 2S LiPo
• BEC: 6,0/7,4V - 4A
• Motorgrens: 10,5T (Let op, belasting afhankelijk!)
• Afmetingen: 40,9x33,9x32,1mm
• Gewicht: 75.4g

XeRun Justock G2.1 17.5T

• Motor: Draaien: 17.5T
• Timing: Fix

 OR-BP1001-13.5T-ETS

ORCA BP1001 Blinky Pro Brushless Speed Controller  (ETS APPROVED)

1up Racing Heatsink Bullet Plug Grips - Fits LowPro Bullet Plugs (2pcs)

Includes 1 pair of 1up Racing 4/5mm Stepped Heatsink Bullet Plugs. Slide the Heatsink Grips over the included LowPro Bullet Plugs and secure with the included set screws. These are perfect for adding some extra bling and improved grip to your charge leads!

1up Racing Heatsink Bullet Plugs - 4mm (2pcs)

1up Racing 4-5mm LowPro Bullet Plugs with Bullet Grips. These are perfectly paired to add to any charge lead where you need 4mm or 5mm bullets. Included with these are the LowPro Bullet Plug Grips. These are a great way to quickly identify your positive and negative leads.

Installation of the Bullet Plug Grips is super easy. After soldering, slide the grip over the LowPro bullet and use a couple drops of CA glue to keep it in place.

Includes:

• (2) 4-5mm stepped bullets
• (2) LowPro bullet plug grips

1up Racing Pro Wire Clamp - 12/14 Gauge 3 Wire

This set contains 1* CR7P radio and 2* R7FS receiver units
 
This remote control system uses the new 2.4 GHz ANT protocol - "enhanced automatic frequency hopping digital system", consisting of a CR7P transmitter and a R7FS receiver. 
There are 7 channels available. The system is ideally suited for crawlers, on-road cars, off-road cars, drift cars and boats.
The large 3,5 x 7,0cm DOT Matrix Display shows all selected parameters clearly.
 
FEATURES 
 
Description of the channels:
CH1: Steering wheel
CH2: Throttle (Trigger)
CH3: SW1 knob
CH4: SW2 knob
CH5: SW3 3-way switch
CH6: VR1 rotary switch
CH7: VR2 3-way toggle switch
 
5-way navigation button
5-way trim switch
New "ANT" 2.4GHz protocol
Various MIX functions (program mixer, dual motor mixer, 4-wheel steering mixer)
Supports 4* AA batteries or 2S LiPo battery as power supply
2-way data transmission
20 model memories
Beginner Mode
Timer / lap counter
Standard functions like REV / EPA / SUB TR / D/R and CURVE settings
Internal antenna
Calibration program
Lightweight and compact design weighing only 305g (without batteries)
Up to 300m range
 
SPECIFICATIONS
 
Remote control CR7P:
Frequency: 2.4GHz
Channels: 7
Model type: cars, boats
RF frequency 2.4GHz; ISM: 2.4G protocol ANT
Maximum power: <20 dBm (EIRP) (EU)
Receive sensitivity: ≤-99dBm
Channel resolution: 1024
Undervoltage warning: YES
Date output: PWM/PPM/i-BUS/S.BUS
Input power: 4-9 V/DC
Battery: 1.5 AA * 4 / 2S Lipo (JST)
Data output type: -C- interface
Charging interface: NO
Antenna type: Built-in single coaxial cable antenna
Display Mode 128*64 LCD (DOT matrix screen, backlit)
Distance: ≥300 m (ground)
Working current: approx. 110mA/6V
Temperature range: -10?~+60?
Humidity range: 20-90%
Size: 136.4 x 111.8 x 197.5mm
Weight: 305g
 
Receiver R7FS (2020017):
Model: R7FS
Frequency: 2.4GHz
Channels: 7
Waterproof: NO
RF Frequency: 2.4GHz ISM RF Standard: ANT
Input power: 3.5-9 V/DC
Weight: 8g
Size: 35*23,3*13,3mm 
 
INCLUDED IN THE SET
 
1* CR7P remote controller
2* R7FS receiver
1* Instruction manual (DE/ENG/FR)

Laadkabel voor accu´s met een Tamiyastekker

Brushless-Set Dragster 3 12Turns

Deze Borstelloze sets werden ontwikkeld om zelfs te rijden in natte, vochtige omstandigheden (plassen en regen). Voertuigen en componenten mogen niet worden ondergedompeld in water. Let op de instructies in de gebruiksaanwijzing!

DRAGSTER 3 Motor sensorlos / sensorless
- Windungen / Turns 12T OnRoad/OfRoad
- kV 3700 kV
- Eingang / Input 6-8 NiMH / 2-3S LiPo
- U/min bei 7,4 V / RPM at 7.4V 27,38
- Geschwindigkeit OnRoad Chassis 1/10 / Speed < 67 km/h
- Dauerstrom / Continous current 51 A
- Abgabeleistung / Output 380 W
- Maße / Size( D x L) 36 x 53 mm
- Shaft length 13 mm
- Shaft diameter 3,175 mm
- Gewicht / Weight 175 g

DRAGSTER 3 Brushlessregler / Brushless Controller
- Eingang / Input 6-8 NiMH / 2-3S LiPo
- Dauerstrom / Continous current 100 A
- kurzzeitig / Peak current 180 A
- Taktung / Clock speed 16 kHz
- Gewicht m. Kabel / Weight 90 g

Carson nummer: 906244

EAN nummer: 4005299962448

Brushless-Set Dragster 3 16Turns

Deze Borstelloze sets werden ontwikkeld om zelfs te rijden in natte, vochtige omstandigheden (plassen en regen). Voertuigen en componenten mogen niet worden ondergedompeld in water. Let op de instructies in de gebruiksaanwijzing!

DRAGSTER 3 Motor sensorlos / sensorless
- Windungen / Turns 16T OnRoad/OffRoad
- kV 2500 kV
- Eingang / Input 6-8 NiMH / 2-3S LiPo
- U/min bei 7,4 V / RPM at 7.4V 18.500
- Geschwindigkeit OnRoad Chassis 1/10 / Speed < 45 km/h
- Dauerstrom / Continous current 38 A
- Abgabeleistung / Output 280 W
- Maße / Size( D x L) 36 x 53 mm
- Shaft length 13 mm
- Shaft diameter 3,175 mm
- Gewicht / Weight 175 g

DRAGSTER 3 Brushlessregler / Brushless Controller
- Eingang / Input 6-8 NiMH / 2-3S LiPo
- Dauerstrom / Continous current 100 A
- kurzzeitig / Peak current 180 A
- Taktung / Clock speed 16 kHz
- Gewicht m. Kabel / Weight 90 g

Carson nummer: 906246

EAN nummer: 4005299962462

Info: Tamiyacup geteste motoren zijn voorzien van een sticker. De motoren zijn getest op een spanning van 8,0V. De aangebrachte sticker is behandelt met nagellak. Bij het verwijderen van de sticker is de goedkeuring van de motor voor de Tamiyacup niet meer geldig.

906251 BL Motor Dragster-3 6T

 BL Motor Dragster-3 12T

Dragster-3 Brushless Motor
12 Turns, 3700KV

Carson nummer: 906254

EAN nummer: 4005299962547

 BL Motor Dragster-3 12T

Dragster-3 Brushless Motor
12 Turns, 3700KV

Carson nummer: 906254

EAN nummer: 4005299962547

Electronische Controller Dragster Brushed 70A

De gevoelige snelheidsregelaar voor RC-modellen op schaal 1:10 is waterdicht en kan dus ook in boten worden geïnstalleerd. Het is ook geschikt voor gebruik in 1:10 buggy's, on-road, off-road voertuigen en crawlers. De controller is ontworpen voor 2 tot 3 LiPo cellen, met een T-Plug plug adapter kunnen ook NiMH batterijen gebruikt worden.

Technische gegevens:
- Vooruit: continue/piekstroom 70A/360A
- achteruit: continue/piekstroom 40A/180A
- BEC: 3A/6V
- Accu: 2-3s LiPo 5-9 cellen NiMH
- Model: 1:10 / 1:12 / 1/16 ON-Road, OFF-Road, Boot
- 2S Lipo of 6cells NimH: 540,550motor ≥18T of minder dan 30000rpm@7.2v (Motor in Turns (T))
- Afmetingen: 34,5 mm x 30,2 mm x 18,7 mm
- Gewicht: 39g
- Mode: Boot, auto, crawlers

Leveromvang:
Electrische snelheidsregelaar Dragster Brushed 70A, Tamiya / T-Plug adapter, handleiding.

Carson nummer: 906264

EAN nummer: 4005299006647

ABSIMA 7.4V 500mAh Li-Lion battery
For Absima 1/16 scale RC cars

ABSIMA 7.4V 800mAh Li-Lion battery
For Absima 1/16 scale RC cars

Brushless Regler "Thrust A10 ECO" 50A 1:10 waterdicht 2110007

Battery type: LiPo
Hard Case
Capacity: 4200mAh
C-rate: 30C
Plug system: Tamiya
Balancer plug system: XH
Voltage: 7.4V
Dimension: 137x46x24mm
Weight: 219g

ABSIMA T-plug (Deans) female battery plug to Tamiya male plug

Tamiya female battery plug to T-plug (Deans) male plug

Adapter 4mm bullet plugs (M) - XT60 (F) Compact Version ABSIMA
Features :

• Plug adapter for the connection of 4mm bullet plugs with XT60 plug systems (female). 
• Area of application: Charging adapter

• 1 pc. Adapter

Fine point soldering tip for the AEROX 150HS 220-240V soldering Stations AX069 and AX070 .

Large Bevel soldering tip for the AEROX 150HS 220-240V soldering Stations  AX069  and  AX070 .

Medium Chisel soldering tip for the AEROX 150HS 220-240V soldering Stations  AX069  and  AX070 .

Introducing from AEROX the awesome 150HS Soldering Station.

A fully adjustable quality soldering station at a great price.

This version is the 220-240V version with European plug.

Features

- 150W of power!
 Fully adjustable temperature from 100 to 500 Degrees C.
- Super fast heat up.
- Fantastic tip cleaning solutions.
- Internal solder roll holder - Never lose your solder. Allows solder to be dispensed through the front of the unit so always ready to use. (Not pictured)
- Available with 3 different plugs for UK and Europe (220-240V) and USA (110-120V). 
- Large bevel tip included, optional fine point and chisel tips available.
- Optional  'Helping Hands' to assist when soldering.

Specifications

Model - 150HS
Power - 150W
Input Voltage -  230VAC (UK/EU) (50-60Hz)
Temp. Range - 100-500℃(212-932℉)
Temp. Stability - ±2℃(±4℉) {>200℃(400℉)}
Temp. Compensation - ±50℃(±90℉)
Temp. Display - Digital
Tip to ground impedance - <0.1Ω
Tip to ground voltage - <2mV
Heater - T60 integrated PTC ceramic heater
Cable length - Power cord: 90cm Handle cable: 1.2m
Dimensions main unit: 80 x 184 x 142mm handle: 24.5 x 224mm
Net weight 516g

Alu High-Speed Brushless Fan (Motor 30*30mm) 28.000RPM

Arrowmax compact tyre and battery warmer. The device utilises a compact control unit for easy storage and less pit space needed with the warmer cups being of Arrowmax’s signature black and golden design. They connect to the front side of the case, ensuring easy organisation of the wires. The control unit is equipped with an XT60 connector, allowing to power the tyre warmer using a 13.8V power supply or a 3S LiPo battery. Built-in sensors ensure precise temperature control, independently for the front and rear tyres, and the warmer not only is usable as a tyre warmer but also as a battery warmer using an optional warming bag. Pre-set values ensure performance enhancing and very high user safety.

These tire warmer cups will keep warm in longer time and the outer silicone material will not burn your hands easily.

• Programmable (running mode; drag brake force; voltage cut-off; punch; maximum brake force)
• 50A continious amp

CARSON Accessoires Telemetrie Sensor Set voor Carson Reflex Wheel Ultimate Touch Afstandsbediening.

De CARSON telemetrie add-on/reserve set sensoren vult extra ontvangers aan of vervangt beschadigde sensoren.
Geschikt voor de REFLEX WHEEL Ultimate Touch telemetrie afstandsbediening Art-No. 500500516. De extra ontvanger is geregistreerd onder het Art-Nr.
500501529 beschikbaar.

Omvang van de levering:

• Snelheidssensor
• 1 temperatuursensor voor motor of snelheidsregelaar
• Batterijspanningssensor

Deans female to Tamiya male cable

Dragster 3 Brushless Motor 16

Carson nummer: 906256

EAN nummer: 4005299962561

Info: Tamiyacup geteste motoren zijn voorzien van een sticker. De motoren zijn getest op een spanning van 8,0V. De aangebrachte sticker is behandelt met nagellak. Bij het verwijderen van de sticker is de goedkeuring van de motor voor de Tamiyacup niet meer geldig.

Carson, 906250, Dragster 3 ESC 100A

De nieuwe sensorloze generatie CARSON borstelloze aandrijving is ontworpen voor nog meer kracht en snelheid. De DRAGSTER Brushless-3-motoren bezitten een enorm koppel en een hoog rendement voor een top acceleratie en hoge topsnelheid.

Let op:
Deze Brushlessregler is ontwikkeld, voor in natte en vochtige omstandigheden (plassen en regen). Voertuigen en componenten mogen niet worden ondergedompeld in water. Zorg ervoor dat u de instructies in de de gebruiksaanwijzing volgt!

Leveromvang: Brushless, programmering doos, handleiding

Technische gegevens:
- 100A ESC waterdicht
- T-Plug

Brushless Controller:
Vooruit / rem / achteruit geschikt voor 6-8 NiMH of 2-3S LiPo cellen
Continue stroom: 100 A / kort: 180 A
Frequentie: 16 kHz
Gewicht: 90 g

Carson nummer: 906250

CARSON Dragster Turbo 2.0 2600KV

CARSON Dragster Turbo 2.0 3200KV

Inbegrepen:
Dragster Turbo 60 A snelheidsregelaar, borstelloze motor, handleiding.

Details:
- 60 A controller waterdicht
- Continue stroom / piekstroom 60 A / 360 A
- 2 S Lipo accu
- Motortype / sensor & borstelloze motor voor
- Accu: 2 S Lipo of 6 cellen NiMH

Technische gegevens motor:
- Borstelloze motor: 3200 kV ( tpm/V)
- Stationair toerental: 24.420 tpm
- Uitgangsvermogen: korte termijn ca. 390 watt
- Continue stroom: 53 A
- Afmetingen (DxL): 35,8 x 50 mm
- As-Ø: 3,175 mm
- Gewicht: 148 g

Technische gegevens ESC:
- Brushless ESC: Vooruit/
- Rem/achteruit / geschikt voor
- 6 NiMH / 2S LiPo cellen
- Continue stroom: 60 A
- Korte termijn: 360 A
- Gewicht: 80 g
- Stekker: T-Plug

Let op! Niet geschikt voor kinderen jonger dan 14 jaar.

LET OP: Niet geschikt voor kinderen jonger dan 14 jaar.
De verpakking moet worden bewaard omdat deze belangrijke informatie bevat.
De afbeeldingen kunnen afwijken van het product in de verpakking.
TAMIYA-CARSON behoudt zich het recht voor om op elk moment verbeteringen en wijzigingen aan te brengen.
 

Sand Scorcher / Lunch Box Mini Battery LiFe

A123 LiFEPO4 6,6V 1,1AH 60A

Tamiyaplug and XHR balanceplug.

L*W*H 70x38x20mm, Weight +/- 100g.

Carson SON Reflex Wheel Pro 2 Telemetry

2S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!

2S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!

CHARGE LEAD XH2S BALANCE PORT-RED-1PC

2S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!

Great charging lead for charging receiver and transmitter packs.  4mm input connectors and Futaba output.

- An extremely useful charge lead which can charge and balance two 2S Lipo's simultaneously and acts as 4S charge leads. - Available in 4 colours, Black, Blue, Red and Orange. - 10 AWG wire - 600mm in length - Balance wire 22AWG  4S/5pin XH on charger side - Nylon covering and extremely well made -

Charge Leads XT60 to XH2S Balance Black - Short 2S Lipo charge lead with XT60 charger input plug and 4-5mm battery plugs, including 2mm balance plug. 300mm. Extremely versatile, suits a wide range of chargers!

Competition-LiPo-HV-140C/1S2P-HC-8300mAh-5mm-ABSIMA
The new ABSIMA LiPo batteries represent the current spearhead of development in lithium battery technology and offer new levels of performance. Masterful engineering skills, combined with experience from professional model sport, have resulted in a performance-optimised battery generation that is unrivalled on the track. The addition of graphene gives the battery improved properties such as higher energy density, lower internal resistance, higher discharge rates and a longer life cycle. 
 
Advantages of a graphene-lipo battery:
The ABSIMA Graphene Lipo series can be used as a standard 3.7V LiPo battery or as a high voltage (HV) 3.8V LiPo. But what is the difference between the capacities 3.7V Standard and 3.8V High Voltage? Normal LiPo batteries have a final charge voltage of 4.2V per cell when fully charged. Due to the unique hybrid RS cell structure, the new type can handle a little more and can be charged up to 4.35V. This not only results in more power from the start, but also means that there is more power in each individual cell and therefore longer runtimes can be achieved. 
 
How do I charge HV LiPo batteries?
First check whether your charger contains a programme for charging HV LiPos. It must be possible to set a final charging voltage of 4.35V. If this is the case, HV LiPo batteries can be charged in the same way as conventional LiPo batteries. The maximum charging rate for an ABSIMA Graphene Lipo is 5C (5 times the capacity of the battery).
 
Another very important note on the charging process!
Please be sure to reset the final charging voltage to 4.2V after completing the HV battery charge. Never charge a standard LiPo battery (3.7V) with a final voltage of 4.35V!
 
Good to know:
1. a LiPo battery should never be stored fully charged or discharged (3V under load / 3.5V open circuit voltage). For optimum battery life, it is recommended to store the LiPo battery in a cool room (e.g. cellar) with a charge level between 50%-80% of capacity. A LiPo battery that is 50% charged has a cell voltage of +/-3.85V.
2. HV-Lipos can also be charged with up to 4.2V like normal Lipos. Due to their much more compact design and lower voltage drop under full load, they still offer longer runtimes.
 
FEATURES:
 
Capacity: 8300mAh
Discharge rate (C): 140C
Voltage: 1S (3.8V HV)
Parallel: 2P
Wh: 31.54 
Max. charging current: up to 5C (1C recommended)
Cable: 12AWG - 200°
Balance cable: 22AWG - 200°
Cable connections: 5mm Bullet / T-Plug 
Design: Hardcase
Dimensions: 93*47*15.5mm
Weight: 146g
 
 

Introducing the Contact RC foam tyre truer.  

This New V2 version has improvements in the sliding mechanism for more accuracy and ease of use.

This Contact tyre truer is a manually operated unit made from robust materials, including an excellent carbide cutting bit, usually found on much higher priced truers.

Special 'Quick Skim' feature to allow fast surface refresh of the tyres.
(The cutter can be moved by hand rather than turning the wheel)

Available with or without attractive carry bag.

- Suitable for 1/8th down to 1/12th sizes.
- Carbide cutting blade included.
- 12 volt DC input, with leads included. (Power supply required).
(If using an AC power supply we recommend a minimum of 10A)
- Plexi glass cover. 
- Powerful motor.
- Universal fit arbors.
- Arbor not included, various types available separately.
- +- 3 deg cone adjustment.

Contact Tyre Truer with Bag

Introducing the Contact RC foam tyre truer. This Contact tyre truer is a manually operated unit aimed at the mid range market.

Made from robust materials including an excellent carbide cutting bit usually found on much higher priced truers.

Special 'Quick Skim' feature to allow fast surface refresh of the tyres. The cutter can be moved by hand rather than turning the wheel.

Features:

• Suitable for 1/8th down to 1/12th sizes.
• Carbide cutting blade included.
• 12 volt DC input, with leads included. (Power supply required).
• Plexi glass cover. 
• Powerful motor.
• Universal fit arbors.
• Arbor not included, various types available separately.
• +- 3 deg cone adjustment.

Awesome plug covers that help with the removal of your battery plugs.  Plus, assist you in plugging in the correct polarity. Super bling look! Secures with the grub screw provided