1up Racing Clear Bearing Oil

A free-spinning drivetrain is the heart of every race worthy car. 1up Clear Bearing Oil soaks into metal surfaces providing long lasting protection and low resistance. For ultra free bearings and increased drivetrain efficiency, the choice is Clear!

Features:

• Leakproof Bottle
• Stainless Needle Tip
• Chilfproof Cap
• 8ml Volume (60% More Than the Original Bottles!)

1up Racing CV Joint Oil 8ml - Red

1up Racing Heatsink Bullet Plug Grips - Fits LowPro Bullet Plugs (2pcs)

Includes 1 pair of 1up Racing 4/5mm Stepped Heatsink Bullet Plugs. Slide the Heatsink Grips over the included LowPro Bullet Plugs and secure with the included set screws. These are perfect for adding some extra bling and improved grip to your charge leads!

1up Racing Heatsink Bullet Plugs - 4mm (2pcs)

1up Racing 4-5mm LowPro Bullet Plugs with Bullet Grips. These are perfectly paired to add to any charge lead where you need 4mm or 5mm bullets. Included with these are the LowPro Bullet Plug Grips. These are a great way to quickly identify your positive and negative leads.

Installation of the Bullet Plug Grips is super easy. After soldering, slide the grip over the LowPro bullet and use a couple drops of CA glue to keep it in place.

Includes:

• (2) 4-5mm stepped bullets
• (2) LowPro bullet plug grips

1up Racing Pink Ball Diff Grease - 3g

Formulated with extensive testing from our Factory Drivers and made for modern high-grip indoor racetracks, we are excited to introduce 1up Racing Pink Ball Diff Grease! Our super tacky Ball Diff Grease gives you the on-power steering and high-speed stability needed to push your buggy with confidence and shave away at your lap times. Like all of our greases, 1up Pink is proudly Made in the USA and backed with the 1up Racing Guarantee – Love it or we’ll return it. Pick one up today!

Follow these instructions to build  a buttery-smooth diff that lasts!

Step 1) Clean the outdrives, diff rings, diff balls, thrust rings, thrust balls and diff screw with parts cleaner to ensure they are free of any machining oils or burrs.

Step 2) Apply 1up Pink to the outdrives and install the diff rings.

Step 3) Apply a heavy amount of 1up Pink to the diff rings and outdrive surface area as shown.

Step 4) Pack 1up Pink into the diff gear and install the diff balls.

Step 5) Build the thrust assembly with 1up Gold as shown.

Finish the diff assembly per your instruction manual and set to a very light tension that just allows the diff movement to engage. Wipe away and save any excess 1up Pink that squeezes out.

Break-in is crucial, allow 30-40 minutes to complete these steps. With the car on a stand and no tires installed, insert the tip of a wrench into either outdrive slot and push through to lock the diff movement on that side. Turn on the car and set your throttle center point so the transmission begins rotating slowly. The opposite outdrive should be spinning. After 2-3 minutes turn down the throttle trim so the outdrive stops spinning, switch the wrench to the other side and repeat.

After both sides have spun at a very light tension for 2-3 minutes each, stop the transmission, tighten the diff screw 1/4 turn and repeat. Gradually tighten the screw after each tension has been broken in until you reach the desired setting. Charge up the battery and run the car on track for 3-4 minutes. Adjust the diff if needed and you’ll be good to go!

1up Racing Servo Mounting Screws 4,0mm Thread - zwart (4)

Met de servoschroeven van 1upRacing kunt u uw stuur- of gasservo heel gemakkelijk en precies monteren. De schroefdraad heeft een lengte van 4 mm en de schroeven passen perfect in alle gangbare servo's op de markt. Een verschuiving van de servo bij een crash wordt voorkomen door deze schroeven van 1upRacing.

De 4mm schroeven zijn verkrijgbaar in zwart, blauw en oranje!

1up Racing Servo Mounting Screws 4,0mm Thread - blauw (4)

Met de servoschroeven van 1upRacing kunt u uw stuur- of gasservo heel gemakkelijk en precies monteren. De schroefdraad heeft een lengte van 4 mm en de schroeven passen perfect in alle gangbare servo's op de markt. Een verschuiving van de servo bij een crash wordt voorkomen door deze schroeven van 1upRacing.

De 4mm schroeven zijn verkrijgbaar in zwart, blauw en oranje!

1up Racing Servo Mounting Screws 4,0mm Thread - Orange (4)

Met de servoschroeven van 1upRacing kunt u uw stuur- of gasservo heel gemakkelijk en precies monteren. De schroefdraad heeft een lengte van 4 mm en de schroeven passen perfect in alle gangbare servo's op de markt. Een verschuiving van de servo bij een crash wordt voorkomen door deze schroeven van 1upRacing.

De 4mm schroeven zijn verkrijgbaar in zwart, blauw en oranje!